Bulk Rack Shelving is the best choice for storing heavy, bulky items. It allows clear and convenient access from front or rear. Shelf spans of 96” W x 48” D are available. Uprights are pre-welded for fast assembly and strength. Each unit can handle load capacities up to 10,000 pounds. Beams incorporate a unique tapered finger design attachment that locks beams safely onto uprights. Two styles of beams and deck supports lets you choose between several different shelf options.
(Single Upright) consist of two parallel upright posts joined by a truss like arrangement of channels; Mig Welded into the opposite slots of the posts. Each post has a footplate with a 9/16” hole for floor mounting. Entire assembly is painted. The upright is rolled form 14 gauge cold rolled steel into a 1 ¾” square with three solid sides and one side with a 27/32” slot along it’s length, for the above channels. The side opposite the slot has holes for the box beam fingers on 2” centers along the entire length. The two other sides have 7/16” x 9/16” holes on the 1” centers along the entire length. The connecting channels are formed from 14 gauge steel, 27/32” wide and 1” deep. The footplate is 2 /14” wide x 3 ½” long stamped from 11 gauge steel with a 9/16” floor mounting hole.
The box beams are constructed of 14 gauge steel formed into a channel formation with the front face 3 ¼” tall and top and bottom flanges 1” deep. The beam has pairs of interior shoulder rivets that accepts SDS-XXB Front to Back Deck Supports.
Front to Back Shelf Deck Support
The front to back shelf deck supports are constructed of 14 gauge steel formed to fit from front to back between two BHC-XX BEAMS. The SDS-XXB shall give the shelf intermediate support.
Consist of a beam and two end plates, same as the above box beam. The new plywood beam has a Z shaped cross-section with a 23/32” wood retainer flange on top of the Z. The beam is 1 3/8” wide x 3 41/64” high wand is formed with 14 gauge steel. It has ¼” x 1 1/8” slots on the top of the Z, along its length, for bulk plywood supports.
Plywood Support Angle
This angle is made from 14 gauge steel. Its purpose is to support the plywood between the supporting box beams. It is 1 59/64” high x 1 1/16” wide. The ends of the angle have a vertical tab, which fit into the ¼” x 1 1/8” slots along the length of the plywood beams.
Bulk Storage Units are fabricated of high quality, cold rolled carbon steel, free of scale or rust and fully pickled. Exposed edges, corners and surface areas are free of sharp edges and all workmanship is of the highest quality as measured by the industry.
All steel components shall be thoroughly cleaned and phosphatized from rust resistance in a five-stage pre-treatment process. A high grade of polyester/epoxy powder paint is to be applied electrostatically with a gloss reading of between 55 and 65. The finish shall have a salt spray rating of 250 hours or more.
Welded uprights makes installation fast and convenient
Beams simply slide into place. Assembly takes less than half the time of most other shelving system.
Box Beam Plywood Holder
Converts a Box Beam to hold particle board decking.
Rolled formed steel box beams provide added strength at the front and back of shelf edges.
Plywood Beam & Braces
Plywood Beam is used to hold wood decking or currugated steel decking and is reinforced with a plywood support angle.
Three Types of Decking
Choose between wire, particle board and corrugated metal decking depending on your application
Retail Storage – shoe, handbag, cosmetics, small and large boxed merchandise, electronics, appliances, furniture, housewares, warehouse
Tab Style Shelving enhances any area with superior design and product quality. The “Box” form creates incredible durability and the powder coating minimizes sharp edges and provides an attractive, smooth finish
Wire Style Shelving is NSF approved. Wire shelving reduces dust build-up, allows free light and air circulation, increases sprinkler effectiveness and improves visibility. It is fast and easy to install with no special tools required.
Clip Style Shelving is the system of choice when heavy duty steel shelves are required. It is a strong, versatile and cost effective shelving system. Clip Style Shelving features steel shelves with a welded box beam construction, lapped/welded corners and triple bends on the side flanges.
Pallet Rack Shelving provides the widest ranges of flexibility for your pallet and heavy duty storage needs. Stocking vertically and horizontally maximizes available space without crushing inventory, while having the ability to access each individual load.